Tính Năng Nổi Bật:
| General | |
| Type | Line array element |
| Transducers | 2x 12” neodymium magnet woofer with 2.5” voice coil |
| 2x compression driver with 2.5” voice coil | |
| Frequency Response | 120 Hz – 19 kHz (-6 dB) |
| Maximum SPL | 138 dB (peak) |
| Coverage | 110° horizontal; |
| 20° vertical (preset dependent) | |
| Internal Processing | |
| Input Sample Rate and Resolution | Up to 96 kHz @ 24 bit with internal SRC and jitter correction |
| Built-in DSP | Input gain, delay up to 330 ms |
| 8 full parametric IIR filters (Peaking, Shelving, Hi/Lo pass, Hi/Lo Butterworth) | |
| FIR filter for electronic beam steering | |
| Onboard presets | |
| Level and temperature remote monitoring | |
| Internal amplifier module | |
| Type | 2 ch., switch-mode class D |
| Peak Output Power | 2x 1600 W @ 4 Ω 1% THD+N |
| Operating Range | 100-240V AC, 50-60 Hz with PFC |
| Power Consumption | 300 W @ 8 Ω load, Pink noise 1/8 rated power |
| Protections | Over Temp. (Power Limiting – Thermal Shutdown), Short Circuit/Overload Output Protection, |
| Power Limiting, Clip Limiter/Permanent Signal Limiter, High Frequency Protection | |
| Mains Connector | powerCON with link inlet |
| Controls and Connectivity | |
| Controls | Remote control with dedicated PC software via USB or RS485 |
| Onboard touch screen display | |
| Connectivity | |
| Analog: | Remote connectivity: |
| 2x XLR (bal) input signal | 1x XLR RS485 serial input |
| 2x XLR (bal) parallel output | 1x XLR RS485 serial output |
| Digital: | 1x USB-B inlet |
| 1x XLR AES3 input | MAINS: |
| 1x XLR AES3 output | 1x powerCON |
| 1x powerCON link | |
| Handling and Finish | |
| Dimensions (WxHxD) | 1218 x 456 x 210 mm (47.9 x 17.9 x 8.3 in) with rigging hardware |
| 1104 x 370 x 200 mm (43.5 x 14.5 x 7.9 in) net dimensions | |
| Weight | 43.6 kg / 96.12 lbs (with rigging hardware) |
| IP rating | 20 (53 with K-AMPCOVER accessory) |
| General | |
| Type | Line array element |
| Transducers | 2x 12” neodymium magnet woofer with 2.5” voice coil |
| 2x compression driver with 2.5” voice coil | |
| Frequency Response | 120 Hz – 19 kHz (-6 dB) |
| Maximum SPL | 138 dB (peak) |
| Coverage | 110° horizontal; |
| 20° vertical (preset dependent) | |
| Internal Processing | |
| Input Sample Rate and Resolution | Up to 96 kHz @ 24 bit with internal SRC and jitter correction |
| Built-in DSP | Input gain, delay up to 330 ms |
| 8 full parametric IIR filters (Peaking, Shelving, Hi/Lo pass, Hi/Lo Butterworth) | |
| FIR filter for electronic beam steering | |
| Onboard presets | |
| Level and temperature remote monitoring | |
| Internal amplifier module | |
| Type | 2 ch., switch-mode class D |
| Peak Output Power | 2x 1600 W @ 4 Ω 1% THD+N |
| Operating Range | 100-240V AC, 50-60 Hz with PFC |
| Power Consumption | 300 W @ 8 Ω load, Pink noise 1/8 rated power |
| Protections | Over Temp. (Power Limiting – Thermal Shutdown), Short Circuit/Overload Output Protection, |
| Power Limiting, Clip Limiter/Permanent Signal Limiter, High Frequency Protection | |
| Mains Connector | powerCON with link inlet |
| Controls and Connectivity | |
| Controls | Remote control with dedicated PC software via USB or RS485 |
| Onboard touch screen display | |
| Connectivity | |
| Analog: | Remote connectivity: |
| 2x XLR (bal) input signal | 1x XLR RS485 serial input |
| 2x XLR (bal) parallel output | 1x XLR RS485 serial output |
| Digital: | 1x USB-B inlet |
| 1x XLR AES3 input | MAINS: |
| 1x XLR AES3 output | 1x powerCON |
| 1x powerCON link | |
| Handling and Finish | |
| Dimensions (WxHxD) | 1218 x 456 x 210 mm (47.9 x 17.9 x 8.3 in) with rigging hardware |
| 1104 x 370 x 200 mm (43.5 x 14.5 x 7.9 in) net dimensions | |
| Weight | 43.6 kg / 96.12 lbs (with rigging hardware) |
| IP rating | 20 (53 with K-AMPCOVER accessory) |
Khuyến Mãi : Giao hàng và lắp đặt miễn phí.
